Satel INTEGRA Especificaciones descargar pdf (Pagina 31)

SATEL Installer Manual 29

When adding and removing the wireless devices, remember that the identification function

registers zones and outputs by groups of 8. Already after adding one wireless device which

takes up 1 zone, the control panel will reserve 8 zones in the system for wireless devices.

The LCD keypad makes it possible to select the zone to which that device will be assigned.

It is necessary to observe continuity, i.e. to avoid leaving gaps in the list, which will later

reduce the number of available zones in the system. You should also remember to maintain

continuity when removing wireless devices from the system. For example, if the devices

registered in the control panel occupy 9 items on the list, then 16 zones are reserved in the

system (2x8). After removal of the device which occupied item 7 on the list, there will still be

16 zones (2x8) reserved in the system for wireless devices, although 8 items are actually

taken up on the list of wireless devices (see: Table 4). In such a case, it is recommended that

the last devices be removed from the list and then added to the system again, so as to fill the

gap created in the list and reduce the number of zones in the system which are needlessly

reserved for wireless devices.

In case of devices which also occupy outputs along with zones, it is recommended that they

be added to the system first, so as not only to maintain the continuity of utilization of the

zones, but of the outputs as well. Shown in Table 4 is situation in which the first output of the

siren occupies place 8, and the second output - place 9. As a result, 16 outputs are reserved

in the system for wireless devices, though actually 2 are used (the eighth output in the first

group of 8 outputs and the first output in the second group of 8 outputs).

In some cases, gaps in the list of zones/outputs cannot be avoided. It concerns situations

when the number of zones/outputs actually used by the devices is not multiple of 8.

The radio communication has been designed so as to make possible operation of several

INTEGRA 128-WRL control panels and ACU-100 controllers when their operating ranges

overlap. Synchronization with the already working wireless systems is always carried out

when turning on the control panel /controller and after each operation of adding/removing the

supported devices. The synchronization is performed automatically. The number of wireless

devices with overlapping ranges depends on the RESPONSE PERIOD (see: PROGRAMMING

manual) and can be from 150 to 450. The higher the frequency of response, the less devices

can work with their ranges being mutually overlapped.

zones outputs

It. list of devices

No device No device

1 APD-100 detector 9 APD-100 detector 9 unused/unavailable

2 APD-100 detector 10 APD-100 detector 10

unused/unavailable

3 AMD-100 detector 11 AMD-100 detector 11

unused/unavailable

4 AMD-100 detector 12 AMD-100 detector 12

unused/unavailable

5 AMD-101 detector 13 AMD-101 detector 13

unused/unavailable

6 ^ 14 AMD-101 detector 14

unused/unavailable

7 15 unused/unavailable 15

unused/unavailable

8 ASP-105 siren

16 ASP-105 siren 16 ASP-105 siren

9 ^ 17 ASP-105 siren 17 ASP-105 siren

10 18 unused/unavailable 18

unused/unavailable

11 19 unused/unavailable 19

unused/unavailable

12 20 unused/unavailable 20

unused/unavailable

13 21 unused/unavailable 21

unused/unavailable

14 22 unused/unavailable 22

unused/unavailable

15 23 unused/unavailable 23

unused/unavailable

24 unused/unavailable 17

unused/unavailable

Table 4. Example of how wireless devices should not be registered. The system has

reserved 16 zones and 16 outputs for devices occupying 8 items.

1 2 ... 26 27 28 29 30 31 32 33 34 35 36

Comentarios a estos manuales

Sin comentarios

Satel INTEGRA Especificaciones Pagina 31

Comentarios a estos manuales

Relacionado con productos y manuales para Monóxido de carbono (co) detectores Satel INTEGRA