Satel INTEGRA Especificaciones

Alarm Control Panel Firmware Version 1.07 GDAŃSK integra-wrl_i_en 08/09 INSTALLER MANUAL 1471

8 INTEGRA 128-WRL SATEL ACU-100. Controller of ABAX wireless system. Enables expansion of the system by additional wireless devices. INT-RX. 433 MHz k

SATEL Installer Manual 9 3.1 INSTALLATION PLAN Installation must be preceded by preparation of a plan of the security alarm system. It is advisable t

10 INTEGRA 128-WRL SATEL regard to hardwired devices (connection of keypads, expansion modules, detectors, sirens, etc.). The control panel should be

SATEL Installer Manual 11 COM +EX DT CKCKMCOMAUXCOM+KPD DTMOUT2COMZ1COMZ2Z3COM Z4Z5Z8COMZ7Z6COMOUT1ACACOUT3

12 INTEGRA 128-WRL SATEL Terminals: AC - power supply inputs (18 V AC) COM - common ground OUT1...OUT2 - programmable high-current outputs (if not

SATEL Installer Manual 13 Notes: • The signal wires (CKM, DTM and COM) must be run in one cable! • The supply voltage measured across the LCD keypa

14 INTEGRA 128-WRL SATEL INTEGRA 128-WRLINT-KLCD-GR/BLINT-KLCDR-GR/BL Fig. 6. Connection of LCD keypad. 3.5.1 Addressing devices connected to keypad

SATEL Installer Manual 15 2. Start the function KEYPAD ADDRESSES (ÆSTRUCTURE ÆHARDWARE ÆIDENTIFICATION ÆKEYPAD ADDRESSES). 3. The message shown i

16 INTEGRA 128-WRL SATEL Z1 Z2 Keypad address Zone number in security system 0 113 114 1 115 116 2 117 118 3 119 120 4 121 122 5 123 124 6 125 126

SATEL Installer Manual 17 number of wires in signal cable distance between module and control panel CK DT COM up to 300 m 1 1 1 300 – 600 m 2

WARNINGS For safety reasons, the security alarm system should only be installed by qualified personnel. Before you begin the installation, read carefu

18 INTEGRA 128-WRL SATEL expanders must be independently supplied (by means of a separate cable from the control panel, expander with power supply, or

SATEL Installer Manual 19 The control panel only supports the modules which are registered in the system by means of the EXPANDER IDENTIFICATION serv

20 INTEGRA 128-WRL SATEL • EOL (end of line resistor), • 2EOL/NC (double end of line resistor, NC type detector), • 2EOL/NO (double end of line re

SATEL Installer Manual 21 Information on powering detectors connected to expanders can be found in section CONNECTING DEVICES TO EXPANDER BUS. Figure

22 INTEGRA 128-WRL SATEL INTEGRA 128-WRLR1R2NC TMP COM12VNC TMP2EOL/NC Fig. 17. Exemplary connection of NC type detector in 2EOL configuration to con

SATEL Installer Manual 23 Notes: • If programmable high-current outputs are not used, they should be loaded with 2.2 kΩ resistor. • The programmabl

24 INTEGRA 128-WRL SATEL INTEGRA 128-WRLP2P1TMPTMPSENS.TMPSASOSP-4001 Fig. 21. Connection of siren without own power supply (by the example of SP-400

SATEL Installer Manual 25 45TXDCOMDSR1562RXDCOMDTR Fig. 22. Printer connection by means of DB-9 male plug (solder side view). TXDCOMDSR156RXDCOMDT

26 INTEGRA 128-WRL SATEL The INTEGRA 128-WRL control panel must be supplied with 18 V (±10%) alternating voltage. Use the transformer secondary windin

SATEL Installer Manual 27 2. The control panel program checks the control panel data saved in the RAM memory (the memory has a battery backup). If no

New functions of the INTEGRA 128-WRL control panels in version 1.07 Zones Option to use resistors of different values in 2EOL configuration. LCD keypa

28 INTEGRA 128-WRL SATEL be no cables running in the immediate vicinity of the antenna, as this may cause interference to radio communication. In orde

SATEL Installer Manual 29 When adding and removing the wireless devices, remember that the identification function registers zones and outputs by gro

30 INTEGRA 128-WRL SATEL zones outputs It. list of devices no device No device 1 ASP-105 siren 9 ASP-105 siren 9 ASP-105 siren 2 ^ 10 ASP-

SATEL Installer Manual 31 − switch on the ARF-100 tester, − insert the ASW-100 E/ASW-100 F wireless controller into 230 V socket, − insert battery

32 INTEGRA 128-WRL SATEL 4. COMPLIANCE WITH CLC/TS 50131-3 REQUIREMENTS To meet the requirements of CLC/TS 50131-3, you must: • reserve two control p

SATEL Installer Manual 33 Weight...

34 INTEGRA 128-WRL SATEL 6. HISTORY OF THE MANUAL UPDATES Given below is a description of changes as compared with the manual for the control panel wi

2 INTEGRA 128-WRL SATEL CONTENTS 1. General description...

SATEL Installer Manual 3 1. GENERAL DESCRIPTION • Dedicated modern microprocessor-based construction for protection of medium-to-big-size facilities,

4 INTEGRA 128-WRL SATEL – web browser (optionally, with ETHM-1 module connected), – mobile phone with MobileKPD application installed (optionally, w

SATEL Installer Manual 5 • Direct support of up to 48 wireless devices of the ABAX system (up to 48 wireless zones / outputs). • Communication bus

6 INTEGRA 128-WRL SATEL be identified by the control panel as CA-64 Ei. Additionally, the CA-64 Ei expander zones offer support for vibration / roller

SATEL Installer Manual 7 CA-64 DR. Expander for "DALLAS" chip readers. Supports the DALLAS chip readers, enabling execution of the access c